Feature-Packed HDBaseT/HDMI Extenders with Ultra HD/4K Support are Here! |
|
KD-X600ProK - HDBaseT/HDMI via Single CAT5e/6 (Tx + Rx Set) Extenders, support Ultra HD/4K, EDID Control, Hot Plug Control, Full Buffer System, HDMI Pass-through, Ethernet, IR Sensor, Up/Down IR & RS-232 |
- HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback, equalization, and amplification depending on cabling length
- Signal Extension:
- Standard Mode (HDBaseT Class A). Supports resolutions up to 4K/UHD.
- Up to 300 ft. @ 4K/24/25/30/60 using KD-CAT6STP1X cabling
- Up to 250 ft. @ 4K/24/25/30/60 using third-party CAT5e/6 UTP/STP
- Up to 400 ft. @ 1080p/1920x1200 using KD-CAT6STP1X cabling
- Up to 300 ft. @ 1080p/1920x1200 using third-party CAT5e/6 UTP/STP
- Long Range Mode (4K resolutions not supported):
- Up to 600 ft. @ 1080p/1920x1200 using KD-CAT6STP1X cabling
- Up to 500 ft. @ 1080p/1920x1200 using third-party CAT5e/6 UTP/STP
- 4K/Ultra HD: Support for 4096x2160 or 3840x2160 24/25/30Hz at 4:4:4 or 60Hz at 4:2:0
- EDID Control: Internal library features 14 default EDID configurations and native EDID data from Output/Display devices connected via Rx
- Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to connected input device
- Full Buffer System™: Manages TMDS re-clocking / signal re-generation, HDCP authentication to source & display, and EDID Control handshake
- HDMI Pass-through: Port on Tx unit connects additional devices up to 20 ft.
- IR Sensor: Sensor powering via +5V on IR In ports collects line-of-sight IR from remote(s) without external IR connecting block
- Up/Down IR: Two channels of IR enable control to/from devices connected to Tx and Rx units
- RS-232: Bi-Directional control to/from Tx and Rx unit on DB9 connector
- RS-232 Control Mode: Provides control of Tx unit as well as connectivity status
- Ethernet: Bi-directional control and/or 10/100 LAN network via TCP/IP RJ45 port
- 3D: Support for standard 3D stereoscopic signal formats
- Deep Color Support: 12bit Deep Color video / 8bit color for 4K/60
- CEC Support: For inter-device control between main input and output HDMI channel
- Lossless compressed digital audio: Support for Dolby® TrueHD, Dolby® Digital Plus and DTS-HD Master Audio™
- Daisy Chaining: Connection of Tx and Rx units allows almost unlimited extension of HDMI, RS-232, IR and Ethernet signals
- HDMI® and HDCP Licensing: Fully licensed and compatible with all HDMI and HDCP technologies
- I2C Communication: EDID and HDCP authentication to Display and Source
- Control System Support: Compatible with Compass Control®, AMX®, Control4®, Crestron®, KNX®, RTI®, Savant, URC®, Honeywell®, HAI®, Leviton® etc.
|
KD-X400ProK - HDBaseT/HDMI via Single CAT5e/6 (Tx + Rx Set) Extenders, EDID Control, Hot Plug Control, Full Buffer System, IR Sensor, Up/Down IR & RS-232,support Ultra HD/4K |
- HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback, equalization, and amplification depending on cabling length
- Signal Extension:
- Standard Mode (HDBaseT Class A). Supports resolutions up to 4K/UHD.
- Up to 150 ft. @ 4K/24/25/30/60 using KD-CAT6STP1X cabling
- Up to 125 ft. @ 4K/24/25/30/60 using third-party CAT5e/6 UTP/STP
- Up to 250 ft. @ 1080p/1920x1200 using KD-CAT6STP1X cabling
- Up to 200 ft. @ 1080p/1920x1200 using third-party CAT5e/6 UTP/STP
- 4K/Ultra HD: Support for 4096x2160 or 3840x2160 24/25/30Hz at 4:4:4 or 60Hz at 4:2:0
- EDID Control: Internal library features 14 default EDID configurations and native EDID data from Output/Display devices connected via Rx
- Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to connected input device
- Full Buffer System™: Manages TMDS re-clocking / signal re-generation, HDCP authentication to source & display, and EDID Control handshake
- IR Sensor: Sensor powering via +5V on IR In ports collects line-of-sight IR from remote(s) without external IR connecting block
- Up/Down IR: Two channels of IR enable control to/from devices connected to Tx and Rx units
- RS-232: Bi-Directional control to/from Tx and Rx unit on DB9 connector
- RS-232 Control Mode: Provides control of Tx unit as well as connectivity status
- 3D: Support for standard 3D stereoscopic signal formats
- Deep Color Support: 12bit Deep Color video / 8bit color for 4K/60
- CEC Support: For inter-device control between main input and output HDMI channel
- Lossless compressed digital audio: Support for Dolby® TrueHD, Dolby® Digital Plus and DTS-HD Master Audio™
- Daisy Chaining: Connection of Tx and Rx units allows almost unlimited extension of HDMI, RS-232, and IR signals
- HDMI® and HDCP Licensing: Fully licensed and compatible with all HDMI and HDCP technologies
- I2C Communication: EDID and HDCP authentication to Display and Source
- Control System Support: Compatible with Compass Control®, AMX®, Control4®, Crestron®, KNX®, RTI®, Savant, URC®, Honeywell®, HAI®, Leviton® etc.
|
KD-X400POHK - Power Over HDBaseT/HDMI via Single CAT5e/6 (Tx + Rx Set) Extenders, EDID Control, Hot Plug Control,
Full Buffer System, IR Sensor, Up/Down IR & RS-232,
supports Ultra HD/4K |
- HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic adjustment of feedback, equalization, and amplification depending on cabling length
- Power Over HDBaseT: Features power extension from Tx to Rx with Power Over HDBaseT, Rx unit does not require power supply
- Signal Extension:
- Standard Mode (HDBaseT Class A). Supports resolutions up to 4K/UHD.
- Up to 150 ft. @ 4K/24/25/30/60 using KD-CAT6STP1X cabling
- Up to 125 ft. @ 4K/24/25/30/60 using third-party CAT5e/6 UTP/STP
- Up to 250 ft. @ 1080p/1920x1200 using KD-CAT6STP1X cabling
- Up to 200 ft. @ 1080p/1920x1200 using third-party CAT5e/6 UTP/STP
- 4K/Ultra HD: Support for 4096x2160 or 3840x2160 24/25/30Hz at 4:4:4 or 60Hz at 4:2:0
- EDID Control: Internal library features 14 default EDID configurations and native EDID data from Output/Display devices connected via Rx
- Hot Plug Detection Control: Enables integrator to choose if active signal voltage is forced to connected input device
- Full Buffer System™: Manages TMDS re-clocking / signal re-generation, HDCP authentication to source & display, and EDID Control handshake
- IR Sensor: Sensor powering via +5V on IR In ports collects line-of-sight IR from remote(s) without external IR connecting block
- Up/Down IR: Two channels of IR enable control to/from devices connected to Tx and Rx units
- RS-232: Bi-Directional control to/from Tx and Rx unit on DB9 connector
- RS-232 Control Mode: Provides control of Tx unit as well as connectivity status
- 3D: Support for standard 3D stereoscopic signal formats
- Deep Color Support: 12bit Deep Color video / 8bit color for 4K/60
- CEC Support: For inter-device control between main input and output HDMI channel
- Lossless compressed digital audio: Support for Dolby® TrueHD, Dolby® Digital Plus and DTS-HD Master Audio™
- Daisy Chaining: Connection of Tx and Rx units allows almost unlimited extension of HDMI, RS-232, and IR signals
- HDMI® and HDCP Licensing: Fully licensed and compatible with all HDMI and HDCP technologies
- I2C Communication: EDID and HDCP authentication to Display and Source
- Control System Support: Compatible with Compass Control®, AMX®, Control4®, Crestron®, KNX®, RTI®, Savant, URC®, Honeywell®, HAI®, Leviton® etc.
|
Upcoming Events |
|
Upcoming Webinars |
|
Upcoming Key Digital Trainings |
In-House Training and Certification Sessions on Compass Control®
9:00 am - 5:00 pm
Hotel / Lunch Included |
Please bring a PC or
Mac with VM Software (Windows)
|
Two-Day Trainings - C1/C2:
September 24-25, 2015
November 5-6, 2015 |
|
Join us for an exclusive Key Digital® Basic and Intermediate level training session on Compass Control®. Trainees will master Compass Control’s modular-based programming methods for iOS devices and the KD-ZRC300 handheld remote.
- Day 1: Compass Control system
introduction, programming KD-ZRC300
ZigBee remote, and modular system
programming for single-zone iOS control.
Integrating with Compass Alliance
Partners for one-app automation and
integration.
- Day 2: IR, RS-232, and TCP-IP
code-set management, editing Compass
Control modules for your core devices,
and building your own multi-zone
automation and integration system with
the Compass Control Modular look & feel.
- Trainees will participate in Compass Control® C1* and C2 Level Certification Exams and be given access to hand-on equipment racks for testing with A/V devices and automation systems. *C1 Certification required to become an Authorized Compass Control® Dealer. No pre-requisite.
|
|
Featured Compass Control® Module |
|
Kaleidescape M-Class products are now compatible with the Compass Control® System, the first fully integrated major control system built from the ground up to use Apple's iOS devices – as its backbone. Compass Control® module enables seamless integration of Kaleidescape products in the Compass Control environment while greatly reducing the installation time for integrators. :: More Information PDF
|
Key Digital Q2 2015 Product Catalog (PDF) |
|
|
|